AienginearTM · VesselCalc Pro Ultimate

v4.0.0 · ASME VIII Div 1 (2025 Ed.) thickness, MAWP, external pressure, volume, weight, testing, MDMT and API 510 life

Shell and head thickness, MAWP

ASME BPVC VIII-1: UG-16, UG-27, UG-32, UG-34, App. 1-2/1-3/1-4, UW-12

1 · Component and mode

2 · Pressure and geometry

Dimensions are entered in the new, uncorroded condition. The calculator adds the corrosion allowance to the inside radius exactly as UG-27 requires ("R = inside radius in the corroded condition").

3 · Material and allowable stress

4 · Weld joint efficiency (Table UW-12)

Heads and spheres use the longitudinal (Category A) value. Seamless heads take E = 1.0 only when the head-to-shell Category B joint meets UW-11(a)(5)(b); otherwise 0.85.

5 · Product form and under-tolerance

ReadyEnter data; results update as you type.
Required thickness t
-
-
t + corrosion allowance
-
UG-16.2 minimum applied
Minimum to order
-
incl. under-tolerance
Selected nominal
-
next standard plate
MAWP, hot and corroded
-
at the analysed wall
MAWP at top (less static head)
-
component value
MAP, new and cold
-
no CA, S at ambient
Utilisation
-

Code checks and notes

    Calculation with your numbers

    -

    External pressure and vacuum: cylindrical shell

    ASME VIII-2 4.4.5 closed form · UG-28 screening estimate

    Inputs

    How this is checked

    Division 1 rates external pressure with the UG-28 chart procedure (factor A from Section II Part D Fig. G, factor B from the material chart). This tool reports two independent screens and takes the lower: the closed-form Division 2 paragraph 4.4.5 method, and a UG-28-style estimate using the Windenburg–Trilling elastic approximation of Fig. G with B capped at Sy/2. For a Code stamp, confirm the final wall with the chart procedure of the edition in force.

    -
    Allowable external pressure
    -
    lower of the two screens
    Div 2 4.4.5 Pa
    -
    -
    UG-28 estimate Pa
    -
    -
    Required wall for this vacuum
    -
    nominal, incl. CA

    Intermediate values

    Notes

      Vessel volume, liquid level and weight

      Numerical integration of the true head profile

      Geometry

      Weight inputs

      Total internal volume
      -
      -
      Liquid volume at level
      -
      -
      Each head volume
      -
      -
      Head depth (inside)
      -
      tangent line to crown
      Empty weight
      -
      plates + allowance
      Full of water (hydrotest)
      -
      foundation / saddle load case
      Operating weight
      -
      at the entered level
      Internal surface area
      -
      shell + both heads

      Level-volume table (printable gauge chart)

      Hydrostatic and pneumatic test pressure

      UG-99, UG-100 · VIII-2 8.2/8.3 · EN 13445-5 · PD 5500 3.8

      Inputs

      Good practice reminders

      • Use the lowest stress ratio (LSR) of all pressure parts, excluding bolting, as UG-99(b) requires.
      • Hold, then inspect at not less than the test pressure divided by 1.3 (Div 1 hydrotest).
      • Test metal temperature should be at least 30 °F (17 °C) above the MDMT for vessels where brittle fracture is a concern.
      • Pneumatic tests store large energy: use an exclusion zone sized by the stored-energy figure and a documented procedure (for example ASME PCC-2 Article 5.1).
      -
      Test pressure at top
      -
      -
      Pressure at bottom
      -
      adds the water column
      Lowest stress ratio
      -
      S test / S design
      Shell membrane stress at test
      -
      -
      Inspection pressure
      -
      test pressure / 1.3 (hydro) or / 1.1 (pneumatic)
      Pneumatic stored energy
      -
      isentropic expansion

      Multi-code comparison: same vessel, four codes

      VIII-1 · VIII-2 Part 4.3 · EN 13445-3 clause 7 · PD 5500 3.5

        Minimum design metal temperature: carbon and low-alloy steel

        UG-20(f) · UCS-66 · Fig. UCS-66.1 · UCS-68(c)

        Inputs


        -
        Table UCS-66 value
        -
        -
        Fig. UCS-66.1 reduction
        -
        -
        MDMT without impact test
        -
        -

        Notes

          In-service: corrosion rate, remaining life and inspection interval

          API 510 (11th Ed.) · API RP 572

          Thickness data

          -
          Corrosion rate
          -
          -
          Remaining life
          -
          (t act − t req) / CR
          Max internal / on-stream interval
          -
          -
          Max external interval
          -
          lesser of 5 years or internal
          Projected wall at next inspection
          -
          -

          Notes

            Vessel summary: all components

            Vessel MAWP = lowest component MAWP corrected to the top

            Formulas, references and built-in QA

            Self-test runs every time the tool loads
            ASME VIII-1 internal pressure (corroded dimensions)
            Cylinder, circumferential stress  UG-27(c)(1)  t = PR / (SE − 0.6P)          valid P ≤ 0.385SE, t ≤ R/2
            Cylinder, longitudinal stress     UG-27(c)(2)  t = PR / (2SE + 0.4P)          valid P ≤ 1.25SE
            Thick cylinder                    App. 1-2     t = R(√Z − 1),  Z = (SE + P)/(SE − P)
            Sphere / hemispherical head       UG-27(d)     t = PR / (2SE − 0.2P)          valid P ≤ 0.665SE, t ≤ 0.356R
            Thick sphere                      App. 1-3     t = R(Y^(1/3) − 1),  Y = 2(SE + P)/(2SE − P)
            Ellipsoidal head                  App. 1-4(c)  t = PDK / (2SE − 0.2P),  K = [2 + (D/2h)²]/6   (K = 1 for 2:1)
            Torispherical head                App. 1-4(d)  t = PLM / (2SE − 0.2P),  M = [3 + √(L/r)]/4   (0.885PL/(SE − 0.1P) for r = 0.06L)
            Conical section, α ≤ 30°          UG-32        t = PD / [2cos α (SE − 0.6P)]
            Flat head                         UG-34        t = d √(CP/SE)
            Minimum thickness                 UG-16.2      1/16 in (1.5 mm) excl. CA; 3/32 in air/steam/water CS; 1/4 in unfired steam boilers
            MAWP (cylinder)                               min[ SEt/(R + 0.6t) , 2SEt/(R − 0.4t) ]
            External pressure (cylinder)
            Div 2 4.4.5:  Mx = L/√(Ro t);  Ch from Mx;  Fhe = 1.6 Ch Ey t/Do
                         Fic = Fhe (Fhe/Sy ≤ 0.552) | 0.7Sy(Fhe/Sy)^0.4 | Sy (≥ 2.439)
                         FS = 2.0 (Fic ≤ 0.55Sy) | 2.407 − 0.741Fic/Sy | 1.667;  Pa = 2 (Fic/FS) t/Do
            UG-28 style: A ≈ 1.3(t/Do)^1.5 / [L/Do − 0.45(t/Do)^0.5]  (≥ 1.1(t/Do)²);  B = min(AE/2, Sy/2);  Pa = 4B / [3(Do/t)]
            Testing, MDMT, in-service
            Div 1 hydrotest   UG-99(b)   PT = 1.3 · MAWP · LSR         pneumatic UG-100: 1.1 · MAWP · LSR
            Div 2 hydrotest   8.2.1      PT = max(1.43 · MAWP, 1.25 · MAWP · LSR)   pneumatic 8.3.1: 1.15 · MAWP · LSR
            EN 13445-5                   PT = max(1.25 · Pd · fa/fT, 1.43 · Pd)
            UCS-66(b) ratio              Rts = tr · E* / (tn − c),  E* ≥ 0.80;  reduction from Fig. UCS-66.1
            API 510                      RL = (t act − t req)/CR;  internal interval ≤ min(RL/2, 10 yr);  RL ≤ 4 yr: ≤ min(RL, 2 yr);  external ≤ 5 yr
            Built-in self-test results
            Reference data status and limitations
            • Code basis: ASME BPVC Section VIII Division 1, 2025 Edition (mandatory for new contracts from 1 January 2026). Paragraph numbers follow that edition; UG-16(b) is now UG-16.2.
            • Not covered: nozzle reinforcement (UG-37), cone-cylinder junctions (App. 1-5), wind, seismic, saddle and lifting loads, fatigue, local loads, flanges. Use the full Code or qualified software for these.
            • This is a preliminary engineering and design-support calculator. It is not a substitute for a Code calculation package reviewed by a qualified engineer and accepted by the Authorized Inspector.