ASME VIII Pressure Vessel Calculator: Thickness, MAWP, Volume & Hydrotest (2026)

AIENGINEAR CALCULATOR · PRESSURE VESSELS · ASME VIII

Updated 27 October 2026 · Calculator v4.0.0 · Standards status checked October 2026 (ASME BPVC 2025, EN 13445-3:2021+A1:2025, PD 5500:2024, API 510 11th Ed.) · By Muhammad Raza

Quick answer: how do you calculate pressure vessel wall thickness?

For a cylindrical shell under internal pressure, ASME Section VIII Division 1 paragraph UG-27 gives t = PR / (SE − 0.6P), where P is the design pressure including any liquid head, R the inside radius in the corroded condition, S the allowable stress at design temperature from Section II Part D and E the weld joint efficiency from Table UW-12. A 2:1 ellipsoidal head needs t = PD / (2SE − 0.2P), roughly the same as the shell; a hemispherical head needs about half. Add the corrosion allowance, check the UG-16.2 minimum of 1/16 in (1.5 mm), allow for pipe under-tolerance or head forming thinning, and round up to a standard plate. The calculator above does all of this, then returns the MAWP, vessel volume and weight, test pressure, MDMT and API 510 remaining life.

Key takeaways

  • The 2025 Edition of the ASME Boiler and Pressure Vessel Code is the current one and became mandatory on 1 January 2026. One change every designer meets: the minimum-thickness rule formerly at UG-16(b) is now UG-16.2.
  • UG-27 uses the corroded inside radius. Using the new radius is a small but common unconservative error.
  • A cylinder has two checks: circumferential (hoop) stress on the longitudinal seams and longitudinal stress on the circumferential seams. With equal joint efficiencies the hoop check governs by a factor of about two.
  • Thin-wall formulas have limits: P ≤ 0.385SE for cylinders and P ≤ 0.665SE for spheres. Beyond them, Mandatory Appendix 1-2 and 1-3 thick-wall equations apply, and this calculator switches automatically.
  • Hydrotest under Division 1 is 1.3 × MAWP × LSR (UG-99(b)); under Division 2 it is the larger of 1.43 × MAWP and 1.25 × MAWP × LSR.
  • Everything runs in your browser. Nothing you enter is uploaded or stored.

Everything runs in your browser; no inputs leave your device. Open the calculator full screen for long sessions, the vessel summary and the printable engineering report.

What is new in calculator v4.0.0

  • Corrected allowable stresses. Carbon steel values now follow the Section II Part D basis for Division 1 (for SA-516 Gr 70, 20,000 psi up to 650 °F), replacing older values that were about 12% low.
  • Corroded radius. UG-27 and UG-32 are now evaluated with the corrosion allowance added to the inside radius, as the Code defines R.
  • Division 2 basis fixed. The comparison uses min(Su/2.4, Sy/1.5) and the 8.2.1 test rule max(1.43, 1.25 × LSR) × MAWP. The old note that Division 2 always demands full radiography has been removed: examination follows the Part 7 groups.
  • New: any ellipsoidal ratio and any torispherical crown/knuckle (Appendix 1-4), thick-wall Appendix 1-2 and 1-3, UG-16.2 minimum thickness, pipe versus plate under-tolerance, forming allowance, external pressure, vessel volume, partial liquid volume, weight, pneumatic stored energy, Table UCS-66 lookup and a printable report with sign-off block.
  • Self-test. 21 reference checks run every time the tool loads; results are withheld if any check fails.

How to use the calculator

The tool is organised as nine tabs that share one set of design data. Enter the vessel once on the first tab and the other tabs pick up the diameter, wall, material and MAWP automatically. Each tab has a checkbox to break that link when you want to study a part on its own.

  1. Choose the component and mode. Design returns the required thickness and a standard plate; Rating takes an existing wall and returns its MAWP. Use rating for re-rating old equipment or checking a vendor’s datasheet.
  2. Enter the design pressure and any liquid head. The static head of liquid above the part is added to the internal pressure, as UG-22 requires, so the bottom head of a full vertical vessel is checked at the higher pressure it actually sees.
  3. Enter the new inside diameter and the corrosion allowance. The tool adds the allowance to the radius before applying the formulas.
  4. Pick the material and design temperature. The allowable stress, yield and tensile strength are filled from the reference library. Untick the library box to enter your own values from Section II Part D, which you must do for the final design.
  5. Set the weld joint type and examination. The joint efficiency E for the longitudinal and circumferential seams comes from Table UW-12.
  6. Choose the product form. Plate allows the small mill under-tolerance waiver; pipe adds 12.5%.
  7. Read the status banner and the checks list before the numbers. Any thick-wall switch, geometry limit or temperature problem is flagged there.
  8. Add the part to the vessel summary, repeat for each head and shell course, then print the full report. The summary picks the governing component and the vessel MAWP at the top.

Practical tip

Design the heads first. A 2:1 head with the same joint efficiency needs almost exactly the shell thickness, but a seamless head (E = 1.0) is often thinner than a spot-radiographed shell (E = 0.85). If the head is thinner, it is usually the shell that sets the vessel MAWP, and an extra 1/16 in on the shell can buy you a higher rating cheaply.

What is a pressure vessel?

A pressure vessel is a closed container designed to hold a gas, vapour or liquid at a pressure substantially different from the surroundings. Separators, reactors, receivers, columns, accumulators, the shells of heat exchangers and storage bullets are all pressure vessels. Their failure releases stored energy suddenly, which is why almost every jurisdiction regulates their design, fabrication, inspection and repair.

ASME Section VIII Division 1 covers vessels above 15 psig (103 kPa) internal or external pressure, with exclusions listed in U-1: for example, vessels with an internal or external operating pressure not exceeding 15 psi, vessels with an inside diameter, width, height or cross-section diagonal not exceeding 6 in (152 mm), and fired process tubular heaters. Division 1 governs design up to 3,000 psi (20 MPa) as a general rule; above that, Division 2 or Division 3 is normally used. A vessel built to Division 1 carries the ASME Certification Mark with the U designator once an Authorized Inspector has accepted it.

The design question is always the same: is the wall thick enough that the membrane stress caused by pressure stays below the allowable stress, with margins for corrosion, fabrication tolerance and testing? Everything in this article is a variation on that question for different shapes and load cases.

Division 1, Division 2, EN 13445 and PD 5500

The four codes most often met on international projects reach the same physical answer by different routes. The main differences are the safety margin on tensile strength, how much analysis and examination they demand, and the hydrotest pressure. A lower margin gives a thinner wall but asks for more engineering and more inspection in return.

Pressure vessel design codes compared

Aienginear Table 1

Pressure vessel design codes compared

Design margins, test pressure and typical use of the four codes in the calculator

Powered by Aienginear
FeatureASME VIII Div 1ASME VIII Div 2EN 13445-3PD 5500
Current edition202520252021+A1:20252024 (+ amendments)
Design approachDesign by ruleDesign by rule or by analysisDesign by formula or by analysisDesign by formula, analysis annexes
Margin on tensile strength (ferritic, at room temperature)3.52.42.42.35
Margin on yield1.51.51.51.5
Shell formulat = PR/(SE − 0.6P)t = (D/2)[exp(P/SE) − 1]e = PDi/(2fz − P)e = pDi/(2f − p)
Hydrotest1.3 × MAWP × LSRmax(1.43, 1.25 × LSR) × MAWPmax(1.25 fa/fT, 1.43) × Pd1.25 × p × fa/ft (× e/(e − c))
Weld efficiencyTable UW-12: 0.60 to 1.00Examination groups (Part 7)Joint coefficient z: 0.7, 0.85, 1.0Construction category 1, 2 or 3
Typical useMost process vessels worldwideHigh pressure, thick wall, cyclic serviceEU Pressure Equipment DirectiveUK and Commonwealth projects
Compiled by Aienginear from the published structure of each code. Margins shown are the governing factors for typical ferritic steels; each code has exceptions. Confirm against the edition in your project specification.aienginear.com/pressure-vessel-calculator/

For a carbon steel drum at moderate temperature the difference is real: the code comparison tab typically shows Division 2 and EN 13445 about 10% thinner than Division 1, and PD 5500 thinner again because it does not reduce the design stress for weld efficiency in the same way. That saving is paid for in examination, documentation and, for Division 2, a user’s design specification and a certified design report.

What changed in the 2025 Edition

ASME publishes the Boiler and Pressure Vessel Code every two years. The 2025 Edition was released in July 2025 and became mandatory on 1 January 2026. For a designer sizing shells and heads, the changes are mostly organisational, but several references in older calculation packages and spreadsheets are now out of date.

  • UG-16(b) is now UG-16.2. The minimum thickness of 1/16 in (1.5 mm), exclusive of corrosion allowance, has a new paragraph number. Quote UG-16.2 in new calculation packages.
  • A new Subsection D in Division 1 gathers component-specific rules. Part UHX (heat exchanger tubesheets) moved there unchanged, and former Mandatory Appendix 24 became Part UCC.
  • More cross-references to Division 2. Flange design in Mandatory Appendix 2 now points to Division 2 paragraph 4.16, and several appendices and UG-35 now refer to Division 2 calculation methods. Expect Division 1 and Division 2 to share more of their equations in future editions.
  • UW-20 tube-to-tubesheet joints now use the yield strength at ambient temperature in the interface-pressure equations.
  • Materials. New entries were added to Tables 1A and 1B and to the external-pressure chart groups, including N08367 in several product forms and N06617 in chart group TE-4.

In Europe, EN 13445-3 received its first amendment to the 2021 edition (A1:2025), with revised rules for openings, non-pressure loads and fatigue. In the UK, PD 5500 is published as the 2024 edition with amendments. Our standards table lists the editions the calculator was checked against.

Why the renumbering matters

Authorised Inspectors and clients increasingly check that a calculation package cites the edition in force at contract. A package that quotes UG-16(b) against a 2025-Edition vessel is not wrong in substance, but it invites a query. The calculator and its printed report cite UG-16.2.

Cylindrical shell thickness (UG-27)

A thin cylinder under internal pressure carries the load as membrane stress in two directions. The circumferential or hoop stress, which tries to split the shell along its length, is twice the longitudinal stress, which tries to pull it apart around its girth. Division 1 writes the two checks with small correction terms that make the thin-wall equations agree with the exact thick-wall (Lamé) solution at the inside surface:

Circumferential stress, longitudinal joints UG-27(c)(1): t = PR / (SE − 0.6P) valid for P ≤ 0.385SE and t ≤ R/2
Longitudinal stress, circumferential joints UG-27(c)(2): t = PR / (2SE + 0.4P) valid for P ≤ 1.25SE

Here R is the inside radius in the corroded condition, which is the new radius plus the corrosion allowance. The joint efficiency E in the first equation belongs to the longitudinal (Category A) seams; in the second, to the circumferential (Category B) seams. The governing thickness is the larger of the two. Because the hoop equation carries SE and the longitudinal one carries 2SE, the hoop check governs unless the circumferential seams have a much lower efficiency than the longitudinal ones.

The same equations rearranged give the maximum allowable working pressure of a given wall:

MAWP = min[ SEt / (R + 0.6t) , 2SEt / (R − 0.4t) ] with t the corroded thickness

When the pressure is high enough that P exceeds 0.385SE, or the wall exceeds half the radius, the thin-wall form is no longer accurate. Mandatory Appendix 1-2 then gives t = R(√Z − 1) with Z = (SE + P)/(SE − P). The calculator applies the switch automatically and says so in the checks list.

Symbols and units used in the ASME VIII thickness equations

Aienginear Table 2

Symbols and units used in the ASME VIII thickness equations

Every quantity in the calculator, with US and SI units

Powered by Aienginear
SymbolQuantityUS unitSI unitNotes
PInternal design pressurepsigMPa (gauge)Includes static liquid head above the part (UG-22)
RInside radius, corrodedinmmNew radius + corrosion allowance
DInside diameter, corrodedinmmFor heads and cones: D at the tangent line or large end
SMaximum allowable stress at design temperaturepsiMPaSection II Part D Table 1A (ferrous) or 1B (non-ferrous)
EWeld joint efficiency––Table UW-12; 1.0 for seamless parts meeting UW-11
tRequired thickness, excluding corrosion allowanceinmmBefore tolerance, forming allowance and rounding
CACorrosion allowanceinmmTypically 1/16 to 1/4 in (1.5 to 6 mm) for carbon steel
KEllipsoidal head factor––[2 + (D/2h)²]/6; equals 1.0 for a 2:1 head
L, rTorispherical crown and knuckle radiiinmmInside dimensions; r ≥ 0.06L and r ≥ 3t
MTorispherical stress factor––[3 + √(L/r)]/4; 1.77 for a standard F&D head
αCone half-apex angledegdegUG-32 rule valid to 30°; beyond that, Appendix 1-5(g)
CFlat head attachment factor––From Fig. UG-34 sketches, 0.17 to 0.33
LSRLowest stress ratio––S at test temperature / S at design temperature (UG-99(b))
Symbols follow ASME Section VIII Division 1; compiled by Aienginear.aienginear.com/pressure-vessel-calculator/

Formed heads, cones and flat heads

A head closes the end of a shell, and its shape decides how efficiently it carries pressure. A hemisphere is pure membrane: its stress is half the hoop stress of a cylinder of the same diameter, so it needs about half the shell thickness. Shallower heads save height and forming cost but introduce bending in the knuckle, the tightly curved band where the dish meets the straight flange, and the thickness climbs accordingly.

Hemispherical head / sphere UG-27(d), UG-32: t = PR / (2SE − 0.2P) valid P ≤ 0.665SE
Ellipsoidal head App. 1-4(c): t = PDK / (2SE − 0.2P), K = [2 + (D/2h)²]/6 (2:1 head: K = 1)
Torispherical head App. 1-4(d): t = PLM / (2SE − 0.2P), M = [3 + √(L/r)]/4 (F&D: 0.885PL/(SE − 0.1P))
Conical section UG-32: t = PD / [2cos α (SE − 0.6P)] α ≤ 30°
Flat head UG-34: t = d √(CP / SE)
Formed head profiles at the same diameter Deeper heads hold more volume and need less thickness; shallow heads save height but pay in knuckle stress Aienginear.com Hemispherical depth 0.50D V = 0.262D³ t ≈ 0.50× 2:1 ellipsoidal depth 0.25D V = 0.131D³ t ≈ 1.00× Korbbogen depth 0.25D V = 0.131D³ t ≈ 1.06× Klöpper depth 0.19D V = 0.099D³ t ≈ 1.54× ASME F&D depth 0.17D V = 0.081D³ t ≈ 1.77× Flat depth 0 V = 0 t ≈ much thicker Orange dashed line = tangent line. Relative thickness compares required t with a 2:1 head of the same D, P, S and E (ASME VIII-1 App. 1-4).
Figure 1. Common head shapes drawn to the same diameter. Depth and volume are fractions of the inside diameter D; relative thickness is computed from Appendix 1-4 for the same pressure and stress. Drawn by Aienginear.

Head types compared at the same diameter and pressure

Aienginear Table 3

Head types compared at the same diameter and pressure

Depth, inside volume, surface area and required thickness relative to a 2:1 ellipsoidal head

Powered by Aienginear
Head typeDepth h/DVolume / D³Inside area / D²t relative to 2:1Typical use
Hemispherical0.5000.26181.5710.50High pressure, large diameter, spheres and bullets
2:1 ellipsoidal0.2500.13091.0841.00The default for process vessels up to roughly 300 psi and above
Korbbogen (DIN 28013)0.2540.13081.0881.06European equivalent of the 2:1 head
Klöpper (DIN 28011)0.1940.09900.9901.54Low to moderate pressure, tanks and receivers
ASME flanged and dished (100% / 6%)0.1690.08100.9311.77Low pressure, atmospheric to about 150 psi; cheapest to form
Flat (welded or bolted)000.785much largerSmall diameters, manways, blind covers
Depth, volume and area computed by Aienginear by numerical integration of the true crown and knuckle profile; relative thickness from ASME VIII-1 Appendix 1-4 with equal P, S and E. Straight flange not included.aienginear.com/pressure-vessel-calculator/

Two head mistakes worth avoiding

First, an ASME F&D head is normally formed with the crown radius equal to the outside diameter. Entering L = D on the inside diameter slightly understates the thickness. Second, pressing a head thins it, most at the knuckle of a torispherical head and at the crown of a hemisphere. The minimum thickness after forming must still meet the calculation. Ask the head maker for their thinning allowance (8 to 12% is typical) and enter it in the forming field.

Cones need special care at both ends. The UG-32 equation gives the membrane thickness of the cone itself, but the junction with the cylinder creates bending that may need a reinforcing ring or a knuckle. Mandatory Appendix 1-5 covers that check and is outside this calculator. Above a 30° half-angle, the simple equation is not permitted at all.

Weld joint efficiency

A welded joint may contain flaws that examination did not find, so the Code reduces the allowable stress across it by the joint efficiency E. The value depends on the type of joint and how much of it was radiographed or ultrasonically examined. Full examination earns E = 1.00 for a double-welded butt joint; spot examination 0.85; none 0.70.

Weld joint efficiency, ASME VIII-1 Table UW-12

Aienginear Table 4

Weld joint efficiency, ASME VIII-1 Table UW-12

Maximum E by joint type and degree of radiographic or ultrasonic examination

Powered by Aienginear
Joint typeDescriptionFull RT/UTSpot RTNone
1Double-welded butt, or equivalent full-penetration butt1.000.850.70
2Single-welded butt with backing strip left in place0.900.800.65
3Single-welded butt without backing––0.60
4 to 6Lap joints (fillet welded)––0.45 to 0.55
SeamlessShell or head with no Category A seam1.001.00 if Cat. B meets UW-11(a)(5)(b)0.85
Compiled by Aienginear from ASME VIII-1 Table UW-12. Some services (lethal, unfired steam boilers above 50 psi, and certain thicknesses) require full radiography regardless of E selected. Lap joints are not offered in the calculator.aienginear.com/pressure-vessel-calculator/

Two details catch people out. A seamless head welded to a shell earns E = 1.0 only if the head-to-shell circumferential seam is spot radiographed to UW-11(a)(5)(b); otherwise the head takes 0.85. And full radiography is mandatory, not optional, for lethal service, for some thicknesses of carbon steel and for unfired steam boilers above 50 psi: check UW-11 before choosing the cheaper examination level.

Allowable stress and materials

For Division 1, the maximum allowable stress S comes from Section II Part D, Table 1A for ferrous materials and Table 1B for non-ferrous. At moderate temperatures it is the lower of the minimum tensile strength divided by 3.5 and two-thirds of the minimum yield strength. Above a material-dependent temperature, creep properties take over and S falls steeply; carbon steel typically starts to drop above 650 °F (343 °C).

Indicative Division 1 allowable stress S for common vessel materials

Aienginear Table 5

Indicative Division 1 allowable stress S for common vessel materials

psi at metal temperature; for screening only, read final values from Section II Part D

Powered by Aienginear
MaterialProduct form100 °F300 °F500 °F650 °FNotes
SA-516 Gr 70Plate20,00020,00020,00020,000Workhorse pressure vessel steel; UCS-66 curve B as-rolled, D normalized
SA-516 Gr 60Plate17,10017,10017,10017,100Better toughness; curve C as-rolled, D normalized
SA-285 Gr CPlate15,70015,70015,70015,700Low-cost plate; curve A
SA-106 Gr BSeamless pipe17,10017,10017,10017,100Nozzle necks and small shells; add 12.5% under-tolerance
SA-240 Type 304Plate20,00015,00012,90012,000Lower (non-G5) values shown
SA-240 Type 316Plate20,00015,60013,30012,300Molybdenum grade, better pitting resistance
SA-240 Type 304L / 316LPlate16,70012,800 / 12,70010,90010,200Low carbon for welded corrosive service
SA-240 S31803 (2205)Plate25,70024,80023,300–Duplex; limited to 600 °F
Indicative values compiled by Aienginear for screening. The austenitic values are the lower set that limits deformation; higher values may apply where slight deformation is acceptable. Always read S from ASME Section II Part D, Table 1A or 1B, of the edition named in your specification.aienginear.com/pressure-vessel-calculator/

Do not use old spreadsheets for S

Allowable stresses for carbon steel rose substantially when the tensile design factor for Division 1 dropped from 4.0 to 3.5 in 1999. Spreadsheets still circulate with SA-516 Gr 70 at 17,500 psi, about 12% below the current value. That error makes walls thicker and test pressures misleading, and it was present in the previous version of this calculator. It is corrected in v4.0.0.

Material choice is about more than S. Toughness at the minimum design metal temperature, corrosion resistance, weldability and availability usually decide it. Our guides to carbon steel grades, stainless steel types and alloy steels cover those trade-offs in more depth.

Corrosion allowance, minimum thickness and under-tolerance

The pressure thickness is only the start. Four further allowances turn it into the plate you order, and each has its own rule.

From calculated thickness to the plate you order Worked Example 1 shell and head, inch. Every layer has its own Code paragraph Aienginear.com Shell 0.214 0.125 0.036 = 0.375 in (3/8) 2:1 head 0.181 0.125 = 0.375 in (3/8) t required (UG-27 / UG-32) corrosion allowance CA forming thinning (heads) round up to standard plate Plate under-tolerance (smaller of 0.01 in or 6%) is waived by UG-16; pipe adds 12.5%. The UG-16.2 minimum does not govern here.
Figure 2. Thickness build-up for Worked Example 1. The calculated pressure thickness is less than two-thirds of the ordered plate; corrosion allowance and rounding make up the rest. Drawn by Aienginear.

Thickness allowances and the paragraphs that govern them

Aienginear Table 6

Thickness allowances and the paragraphs that govern them

What to add to the pressure thickness, and when

Powered by Aienginear
AllowanceRuleTypical valueParagraph
Minimum thicknessShells and heads, exclusive of CA, regardless of pressure1/16 in (1.5 mm); 3/32 in (2.5 mm) carbon steel in compressed air, steam or water service; 1/4 in (6 mm) unfired steam boilersUG-16.2 (UG-16(b) before 2025)
Corrosion allowanceAdded to the required thickness and to the inside radius1/16 to 1/4 in carbon steel; often 0 for stainlessUG-25
Plate under-toleranceNot added if the under-tolerance is not more than the smaller of 0.01 in (0.3 mm) or 6% of the ordered thicknessSA-20 plate: 0.01 inUG-16
Pipe under-toleranceMust be added12.5% for most seamless and welded pipeUG-16
Forming allowanceMinimum thickness after forming must meet t + CA8 to 12% for pressed headsUG-81, UG-16
RoundingUp to the next available plate1/16 in steps (US); 1 or 2 mm steps (SI)Practice
Compiled by Aienginear from ASME VIII-1, 2025 Edition. Corrosion allowance is set by the user’s design specification and the expected corrosion rate over the design life, not by the Code.aienginear.com/pressure-vessel-calculator/

A good corrosion allowance equals the expected corrosion rate multiplied by the design life, rounded up. For a 20-year life at 5 mpy (0.13 mm/y) that is 0.1 in, so 1/8 in (3 mm) is a common choice. Where corrosion is localised, such as pitting in stainless steel or erosion at an inlet, a thicker wall rarely helps; material choice and inlet devices do.

MAWP, MAP and static head

Three pressures appear on every vessel data sheet and are often confused.

  • Design pressure is chosen by the process engineer: normally the maximum operating pressure plus a margin of 10% or 25 psi, whichever is greater, so that the relief valve does not lift during normal upsets.
  • Maximum allowable working pressure (MAWP) is what the actual walls can take in the hot and corroded condition, at the top of the vessel in its operating position. It is the lowest value over all pressure parts, each reduced by the static head acting on it. MAWP is equal to or higher than the design pressure, and it is the upper limit for the relief valve set pressure.
  • Maximum allowable pressure, new and cold (MAP) is the same calculation with no corrosion and the allowable stress at ambient temperature. It is useful for shop testing and for re-rating studies.
The pressure ladder: how the numbers relate Worked Example 1 values, psig. The relief valve set pressure may not exceed the MAWP Aienginear.com Normal operating pressure 130 Design pressure P 150 MAWP (hot, corroded, top) 175 PSV set pressure (≤ MAWP) 175 Allowable overpressure, single PSV: 110% MAWP 193 Fire case: 121% MAWP 212 Hydrotest at top: 1.3 × MAWP × LSR 228 Overpressure limits follow the Division 1 overpressure protection rules (UG-150 series) and API 520/521 practice; 130 psig operating is illustrative.
Figure 3. The pressure ladder for Worked Example 1. The relief valve is set at or below the MAWP; the vessel may briefly exceed it by the allowable overpressure during relief. Drawn by Aienginear.

The calculator reports the component MAWP at its own location and at the top of the vessel, after subtracting the liquid head entered for that part. Add every shell course and head to the vessel summary and it identifies the governing component. When sizing the relief valve, use our PSV relief load calculator; for exchangers with high-pressure tubes, the tube rupture relief suite covers the extra case.

Worked example 1: horizontal drum, US units

A horizontal knock-out drum: 48 in inside diameter, 120 in tangent to tangent, two 2:1 ellipsoidal heads. Design 150 psig at 300 °F, SA-516 Gr 70 plate, corrosion allowance 1/8 in. Shell: Type 1 longitudinal and circumferential seams with spot radiography (E = 0.85). Heads: seamless, with the head-to-shell seams spot radiographed (E = 1.0) and a 10% forming allowance.

S = 20,000 psi (SA-516 Gr 70, 300 °F) R = 24 + 0.125 = 24.125 in D = 48.25 in
Shell hoop: t = 150 × 24.125 / (20,000 × 0.85 − 0.6 × 150) = 3,618.75 / 16,910 = 0.2140 in
Shell long.: t = 150 × 24.125 / (2 × 20,000 × 0.85 + 0.4 × 150) = 0.1062 in → hoop governs
Shell order: 0.2140 + 0.125 = 0.339 in → 3/8 in (0.375) MAWP = 17,000 × 0.25 / (24.125 + 0.15) = 175.1 psi
2:1 head: t = 150 × 48.25 / (2 × 20,000 × 1.0 − 0.2 × 150) = 0.1811 in + CA = 0.306 ÷ 0.90 forming = 0.340 → 3/8 in
Hydrotest: PT = 1.3 × 175.1 × (20,000/20,000) = 227.6 psig at the top

Worked example 1 results: 48 in × 120 in horizontal drum

Aienginear Table 7

Worked example 1 results: 48 in × 120 in horizontal drum

SA-516 Gr 70, 150 psig at 300 °F, CA 1/8 in, 2:1 heads

Powered by Aienginear
ItemShell2:1 headsVessel
Required thickness t0.2140 in0.1811 in–
t + CA0.3390 in0.3061 in–
Minimum to order0.3390 in (plate)0.3401 in (10% forming)–
Nominal plate3/8 in3/8 in–
MAWP, hot and corroded175.1 psig176.0 psig175.1 psig (shell governs)
MAP, new and cold263.2 psig280.9 psig263.2 psig
Hydrotest pressure (UG-99(b))––227.6 psig at top
Total volume–62.7 US gal each1,065 US gal (4.03 m³)
Empty weight (plates + 10%)––about 2,730 lb (1,240 kg)
Full of water––about 11,620 lb (5,270 kg)
Computed with the Aienginear Pressure Vessel Calculator v4.0.0. Reproduce it by entering the inputs above; small differences come from rounding.aienginear.com/pressure-vessel-calculator/

Reading the result

The head and shell end up with the same 3/8 in plate, but for different reasons: the shell because of E = 0.85, the head because of the forming allowance. If the client wants a higher MAWP, upgrading the shell seams to full radiography (E = 1.0) raises the shell MAWP to about 206 psig at the same thickness; the 10% thinner head then governs at 176 psig. Small decisions on examination often matter more than plate thickness.

Worked example 2: vertical stainless vessel, SI units

A vertical buffer vessel: 1,500 mm inside diameter, 3,000 mm tangent to tangent, Klöpper heads (crown radius = D, knuckle = 0.1D). Design 1.0 MPa(g) at 150 °C, SA-240 Type 316L, no corrosion allowance, full radiography (E = 1.0). The vessel runs full of water-like liquid, so the bottom head and the lower shell see an extra 3 m of static head, about 0.029 MPa.

Worked example 2 results: 1,500 mm × 3,000 mm vertical vessel

Aienginear Table 8

Worked example 2 results: 1,500 mm × 3,000 mm vertical vessel

SA-240 316L, 1.0 MPa at 150 °C, Klöpper heads, E = 1.0, CA = 0

Powered by Aienginear
ItemValueComment
Allowable stress S at 150 °C87.4 MPaIndicative library value; confirm in Section II Part D
Design pressure at the bottom tangent1.029 MPa1.0 MPa + 3 m × 9.81 × 1,000 kg/m³
Shell required thickness8.89 mmUG-27(c)(1); P/SE = 0.012, thin-wall valid
Shell nominal10 mmMAWP 1.156 MPa at the bottom tangent
Klöpper head required thickness13.62 mmAppendix 1-4(d), M = 1.541
Head minimum to order (10% forming)15.13 mm→ 16 mm nominal, MAWP 1.088 MPa
Total volume5.97 m³Each head 0.334 m³, head depth 291 mm
Governing partKlöpper headA 2:1 head would need about 9 mm instead of 14 mm
Computed with the Aienginear Pressure Vessel Calculator v4.0.0 in SI mode.aienginear.com/pressure-vessel-calculator/

The lesson of this example is the head choice. A Klöpper head saves about 85 mm of height against a 2:1 head on this diameter but needs roughly 1.5 times the thickness, and in stainless steel that extra plate costs more than the height it saves. Run both options in the calculator before you fix the head type.

External pressure and vacuum

Under external pressure a shell fails by buckling, not by yielding, so thickness alone does not decide the answer: the distance between stiffeners matters as much. Division 1 handles this with the chart procedure of UG-28. You compute L/Do and Do/t, read factor A from the geometric chart in Section II Part D, read factor B from the material chart at the design temperature, and obtain the allowable pressure as Pa = 4B / [3(Do/t)].

The calculator gives two independent screens and reports the lower. The first is the closed-form method of Division 2 paragraph 4.4.5, which replaces the charts with equations for the elastic buckling stress and a design factor. The second reproduces the UG-28 procedure with an elastic approximation of the geometric chart and B capped at half the yield. For a vessel that must withstand full vacuum, enter 15 psi (0.103 MPa) and the unsupported length: the tangent-to-tangent length plus one-third of each head depth, or the spacing between stiffening rings.

Vacuum is a design case, not an accident

Many vessel failures under vacuum happen during steam-out, draining with a closed vent or rapid cooling of vapour. If any of these is credible, design for full vacuum or provide a vacuum breaker and document it. The stiffening rings, cones and heads also need checking under external pressure (UG-29, UG-33); the calculator covers the cylinder only.

Vessel volume and weight

Volume drives residence time, inventory, relief load and the weight of water during hydrotest. The calculator integrates the true head profile numerically instead of using rule-of-thumb constants, so it handles any ellipsoidal ratio and any torispherical crown and knuckle, and gives exact partial volumes at any liquid level.

Shell: V = (π/4) D² L 2:1 ellipsoidal head: V = π D³ / 24 Hemispherical head: V = π D³ / 12
Horizontal shell, liquid height h: V = L [ R² cos⁻¹((R − h)/R) − (R − h) √(2Rh − h²) ]
Level is not volume: horizontal versus vertical 48 in ID × 120 in T-T, 2:1 heads. A horizontal drum gains volume slowly near bottom and top Aienginear.com 0%0% 20%20% 40%40% 60%60% 80%80% 100%100% liquid level, % of total height % of total volume horizontalvertical At 10% level ahorizontal drum holdsonly 4.9% of volume.
Figure 4. Volume fraction against level for the drum of Worked Example 1. A horizontal vessel is non-linear near the bottom and top, which is why level alarms on horizontal drums need a strapping table. Computed and drawn by Aienginear.

The volume tab prints a level-volume table at 10% steps, ready to hand to the instrument engineer for level transmitter ranging. For tanks and atmospheric vessels, the dedicated tank volume calculator and the vessel volume and calibration calculator add more shapes and full strapping tables. For plate and section weights, use the metal weight calculator.

Weight is estimated from the plate volumes plus an allowance for nozzles, supports and internals (10% is a reasonable starting point; trayed columns need much more). The full-of-water weight is the load case for foundations, saddles and lifting during the hydrotest, and it is often the largest load the supports ever carry.

Hydrostatic and pneumatic testing

Every Code vessel is pressure tested before it enters service. The test proves the vessel is leak-tight and gives a degree of mechanical stress relief at sharp details, but it is a proof test: it confirms the design, it does not replace it.

Pressure test requirements by code

Aienginear Table 9

Pressure test requirements by code

Hydrostatic and pneumatic test pressure and the related inspection pressure

Powered by Aienginear
CodeHydrostatic testPneumatic testInspection atNotes
ASME VIII-1 (2025)1.3 × MAWP × LSR (UG-99(b))1.1 × MAWP × LSR (UG-100)PT / 1.3 (hydro); PT / 1.1 (pneumatic)LSR = lowest S(test)/S(design) of the parts, excluding bolting
ASME VIII-2 (2025)max(1.43 × MAWP, 1.25 × MAWP × LSR) (8.2.1)1.15 × MAWP × LSR (8.3.1)As specified in 8.2General membrane stress during test is limited by 8.2.1(c)
EN 13445-5max(1.25 × Pd × fa/fT, 1.43 × Pd)Permitted only with additional safety measuresPer Part 5 procedureCheck national requirements for pneumatic testing
PD 55001.25 × p × fa/ft × e/(e − c) (3.8.5)As hydro, with special precautionsPer Section 5Corrosion allowance term applies to the standard test
ASME B31.3 (piping, for reference)1.5 × design × stress ratio1.1 × design–Use the hydrotest calculator for piping
Compiled by Aienginear from the published rules of each code. Test metal temperature should be at least 30 °F (17 °C) above the MDMT to reduce brittle fracture risk (UG-99(h)). Confirm the paragraph numbers in the edition named in your specification.aienginear.com/pressure-vessel-calculator/

A pneumatic test stores far more energy than a hydrotest of the same vessel, because gas is compressible. The calculator estimates that energy from the isentropic expansion of the test gas and expresses it as a TNT equivalent; for the 4 m³ drum in Worked Example 1 at its pneumatic test pressure it is about 7.7 MJ, roughly 1.8 kg of TNT. That figure, together with a documented procedure such as ASME PCC-2 Article 5.1, sets the exclusion zone.

MDMT and impact testing

Carbon steel loses toughness as it gets colder. Below a transition temperature, a crack can run through the wall at a stress well under yield, without warning. The minimum design metal temperature (MDMT) is the coldest metal temperature the vessel must tolerate at its design pressure, and Division 1 requires either impact testing or an exemption to show the steel is tough enough at that temperature.

UCS-66 assigns each carbon and low-alloy steel to an exemption curve, A to D, with D the toughest. Table UCS-66 then gives the exemption temperature for the governing thickness. If the vessel is lightly stressed, Fig. UCS-66.1 allows a further reduction based on the ratio tr·E* / (tn − c). Post-weld heat treatment that the Code does not require earns a further 30 °F (17 °C) credit for P-No. 1 materials under UCS-68(c).

Impact test exemption temperature by curve (indicative)

Aienginear Table 10

Impact test exemption temperature by curve (indicative)

Table UCS-66 style values for governing thickness tg, °F; screening only

Powered by Aienginear
Governing thicknessCurve ACurve BCurve CCurve D
≤ 0.394 in (10 mm)18−20−55−55
0.5 in (12.7 mm)32−7−34−55
0.75 in (19 mm)5315−15−42
1.0 in (25 mm)6831−3−30
1.5 in (38 mm)885115−14
2.0 in (51 mm)996327−4
3.0 in (76 mm)11176407
Indicative values compiled by Aienginear for screening and education. Use Table UCS-66 of the edition in force for the nameplate MDMT. SA-516 plate is curve B (Gr 65, 70) or C (Gr 55, 60) as-rolled and curve D when normalized.aienginear.com/pressure-vessel-calculator/

A practical consequence: ordering SA-516 Gr 70 normalized moves it from curve B to curve D and lowers the exemption temperature at 1 in thickness from about 31 °F to −30 °F. For any vessel in a cold climate or with auto-refrigeration on depressuring, specify normalized plate at the enquiry stage; it costs little and often removes the need for impact testing.

In-service inspection: API 510

Once a vessel is in service, API 510 governs inspection, repair, alteration and re-rating. The core arithmetic is simple and is built into the calculator’s API 510 tab:

Corrosion rate (long term) CR = (t previous − t actual) / years
Remaining life RL = (t actual − t required) / CR
Internal or on-stream interval ≤ min(RL/2, 10 years); if RL ≤ 4 years: ≤ min(RL, 2 years)
External visual interval ≤ min(5 years, internal interval)

API 510 default inspection intervals (non-RBI)

Aienginear Table 11

API 510 default inspection intervals (non-RBI)

Maximum intervals from the 11th Edition; risk-based inspection may set different values

Powered by Aienginear
InspectionMaximum intervalBasis
Internal or on-streamLesser of half the remaining life or 10 yearsRemaining life from the governing corrosion rate
Internal, short remaining lifeFull remaining life, up to 2 years, when RL ≤ 4 yearsProvided the vessel is not below the required thickness
External visualLesser of 5 years or the internal intervalInsulated vessels add CUI assessment
Pressure-relieving devicesPer API 576 and the owner’s programme (typically up to 5 or 10 years)Depends on service and test history
Risk-based (API RP 580/581)As set by the RBI assessmentMust be reviewed after process changes
Compiled by Aienginear from API 510, 11th Edition (2022) with errata. Jurisdictional rules can be stricter; follow the requirements that apply at your site.aienginear.com/pressure-vessel-calculator/

Use the larger of the pressure thickness and any structural minimum as t required. When the remaining life drops below the next turnaround, the options are repair, re-rating to a lower MAWP, or a fitness-for-service assessment to API 579-1/ASME FFS-1. Planning that work is part of turnaround and shutdown management.

Common design mistakes

  1. Using the new radius instead of the corroded radius. The error is small on thin walls but grows with the corrosion allowance.
  2. Forgetting the liquid head. The bottom head of a 10 m tall vessel full of water sees about 1 bar more than the top.
  3. Applying the shell joint efficiency to a seamless head or, more often, claiming E = 1.0 for a seamless head without the required spot examination of its circumferential seam.
  4. Treating pipe like plate. A shell made from pipe needs its 12.5% under-tolerance added.
  5. Ignoring forming thinning on pressed heads, especially at the knuckle of a torispherical head.
  6. Quoting an out-of-date allowable stress from an old spreadsheet, or a value at the wrong temperature.
  7. Stopping at shells and heads. Nozzle reinforcement (UG-37), flange ratings, saddle and lifting loads, wind and seismic loads often govern more of the vessel than the shell does.
  8. Leaving vacuum to chance. Steam-out and draining with a closed vent create vacuum in vessels never designed for it.

How this calculator compares

Aienginear Pressure Vessel Calculator vs typical free online tools

Aienginear Table 12

Aienginear Pressure Vessel Calculator vs typical free online tools

What most free vessel calculators do, and what this one adds

Powered by Aienginear
CapabilityTypical free calculatorAienginear Pressure Vessel Calculator
Shell and 2:1 head thicknessYesYes, plus any ellipsoidal ratio and any torispherical L and r
Corroded radius per UG-27Often ignoredApplied automatically
Hoop and longitudinal checks with separate ERareYes, with Table UW-12 joint selector
Thick-wall Appendix 1-2 and 1-3NoAutomatic switch with a flag
UG-16.2 minimum, plate vs pipe tolerance, forming allowanceNoYes, with standard plate selection
MAWP hot-corroded, at top, and MAP new-coldUsually one MAWPAll three
External pressure / vacuumRareDiv 2 4.4.5 and UG-28 style screens
Vessel volume, partial volume and weightSeparate toolsBuilt in, true head profiles
Hydrotest and pneumatic stored energyHydrotest onlyFour codes plus stored energy
MDMT (UCS-66) and API 510 lifeNoYes
Four-code comparisonNoDiv 1, Div 2, EN 13445-3, PD 5500
Printable report with sign-off blockNoYes
Built-in self-testNo21 reference checks on every load
Data privacyVariesRuns entirely in the browser; nothing uploaded
CostFree to paidFree, no registration
Aienginear review of commonly available free pressure vessel calculators, October 2026. Third-party tools change; verify current behaviour before relying on this comparison.aienginear.com/pressure-vessel-calculator/

Standards and references

Governing documents and how the calculator uses them

Aienginear Table 13

Governing documents and how the calculator uses them

Standards status checked October 2026; always confirm the edition in your project specification

Powered by Aienginear
DocumentScopeRole in this calculator
ASME BPVC Section VIII Division 1, 2025Rules for construction of pressure vesselsThickness, MAWP, joint efficiency, minimum thickness, testing, MDMT
ASME BPVC Section VIII Division 2, 2025Alternative rulesExponential thickness equations, 4.4.5 external pressure, 8.2 test pressure
ASME BPVC Section II Part D, 2025Material propertiesAllowable stress, yield, modulus, external pressure charts
EN 13445-3:2021+A1:2025Unfired pressure vessels: designNominal design stress and shell formula in the comparison
EN 13445-5:2021Inspection and testingHydrotest formula in the comparison
PD 5500:2024UK specification for unfired pressure vesselsDesign stress, shell formula and test pressure in the comparison
API 510, 11th EditionPressure vessel inspection codeCorrosion rate, remaining life and inspection intervals
API 579-1/ASME FFS-1Fitness for serviceNext step when remaining life is short
API 520 / API 521Pressure relief sizing and installationContext for set pressure and overpressure
ASME PCC-2 Article 5.1Pressure and tightness testingPneumatic test stored energy and safe distances
Compiled by Aienginear. This table is a navigation aid, not a substitute for the standards. External links open the publisher’s page.aienginear.com/pressure-vessel-calculator/

Assumptions and limitations

Stated plainly, so you know where the tool stops and engineering judgement starts.

  • Internal pressure membrane design of shells and heads only. Nozzles and openings (UG-36 to UG-45), cone junctions (Appendix 1-5), flanges (Appendix 2), supports, wind, seismic, local loads and fatigue are not checked.
  • Material data are indicative. The library is a convenience for screening. Final values must come from Section II Part D of the edition named in your specification.
  • External pressure is screened for cylinders. Heads, cones and stiffening rings need the full UG-28 to UG-33 procedure.
  • Table UCS-66 and Fig. UCS-66.1 values are indicative. Below a ratio of 0.6 the tool applies a conservative 40 °F reduction; read the figure for more credit.
  • Weights are estimates from plate volumes plus a percentage allowance.
  • This is a preliminary engineering and design-support calculator. It is not a substitute for a Code calculation package reviewed by a qualified engineer and accepted by the Authorized Inspector, and it is not ASME certified, because no software can be.

Quick quiz: test your pressure vessel knowledge

1. In UG-27, which radius do you use for a shell with a corrosion allowance?

2. What is the Division 1 hydrostatic test pressure?

3. Roughly how thick is a hemispherical head compared with a 2:1 ellipsoidal head at the same pressure?

4. In the 2025 Edition, the minimum thickness rule formerly at UG-16(b) is found at:

5. A shell is made from seamless pipe. What under-tolerance must be added?

The pressure vessel calculator sits in the Aienginear pressure integrity family. These are the tools most often used alongside it.

Frequently asked questions

How do you calculate the thickness of a pressure vessel shell?

Use ASME VIII-1 UG-27: t = PR/(SE − 0.6P) for the circumferential stress and t = PR/(2SE + 0.4P) for the longitudinal stress, and take the larger. R is the inside radius in the corroded condition, S the allowable stress from Section II Part D at design temperature and E the joint efficiency from Table UW-12. Then add the corrosion allowance, apply the UG-16.2 minimum and any under-tolerance, and round up to a standard plate.

What is the formula for a 2:1 ellipsoidal head?

t = PD/(2SE − 0.2P), where D is the inside diameter in the corroded condition. For other ellipsoidal ratios, Mandatory Appendix 1-4(c) multiplies the numerator by K = [2 + (D/2h)²]/6. A 2:1 head needs almost exactly the same thickness as a cylinder of the same diameter and joint efficiency.

What is the difference between design pressure and MAWP?

Design pressure is chosen by the process engineer, usually the maximum operating pressure plus a margin. MAWP is calculated from the actual walls in the hot and corroded condition, at the top of the vessel, and is the lowest value over all pressure parts. MAWP is equal to or greater than the design pressure and is the upper limit for the relief valve set pressure.

What is the hydrotest pressure for an ASME VIII Division 1 vessel?

UG-99(b) requires at least 1.3 × MAWP × LSR, where LSR is the lowest ratio of allowable stress at test temperature to allowable stress at design temperature among the pressure parts, excluding bolting. Visual inspection follows at a pressure not less than the test pressure divided by 1.3.

What changed in the 2025 Edition of ASME Section VIII?

For shell and head sizing, the visible change is that the minimum thickness rule formerly at UG-16(b) is now UG-16.2. Division 1 also gained a Subsection D for component rules (UHX moved there, Appendix 24 became Part UCC), more cross-references to Division 2 methods, revised UW-20 tube-to-tubesheet equations and new materials. The 2025 Edition became mandatory on 1 January 2026.

What is the minimum thickness of a pressure vessel shell?

Under UG-16.2 the minimum is 1/16 in (1.5 mm), exclusive of corrosion allowance, for shells and heads regardless of pressure. Carbon and low-alloy steel vessels in compressed air, steam or water service need 3/32 in (2.5 mm), and unfired steam boilers 1/4 in (6 mm).

Why is the corrosion allowance added to the radius?

UG-27 defines R as the inside radius in the corroded condition. As the wall corrodes from inside, the radius grows, so the hoop stress at the end of life is calculated on the larger radius. Using the new radius gives a slightly thin, unconservative wall.

When do I need the thick-wall equations?

For cylinders when P exceeds 0.385SE or t exceeds half the inside radius, and for spheres when P exceeds 0.665SE or t exceeds 0.356R. Mandatory Appendices 1-2 and 1-3 then apply. The calculator switches automatically and flags the change.

Which head type should I use?

The 2:1 ellipsoidal head is the default for most process vessels because it needs about the shell thickness at moderate cost. Hemispherical heads suit high pressure and large diameters. ASME flanged and dished and Klöpper heads are cheap and shallow but need 1.5 to 1.8 times the thickness, so they suit low pressure.

How do I design a vessel for full vacuum?

Take the external design pressure as 15 psi (0.103 MPa), find the unsupported length between stiffeners or the tangent length plus one-third of each head depth, and check the shell with UG-28. If the wall needed is too thick, add stiffening rings. The calculator screens the cylinder with two independent methods and returns the governing allowable pressure.

How is vessel volume calculated with heads?

Add the shell volume, (π/4)D²L, to two head volumes. A 2:1 ellipsoidal head holds πD³/24 (0.1309D³), a hemispherical head πD³/12 and an ASME F&D head about 0.081D³. The calculator integrates the actual head profile, so it also gives partial volumes at any liquid level.

Does the calculator check nozzle reinforcement?

No. Openings, nozzle reinforcement (UG-37), flange ratings and external loads on nozzles need separate checks. The printed report states this limitation.

Is the Aienginear pressure vessel calculator ASME certified?

No, and no calculator can be. ASME certifies manufacturers, not software. The tool implements the published equations, flags every limit it knows about and runs a self-test on every load. Treat it as a preliminary engineering and design-support calculator subject to review by a qualified engineer.

Is my data sent anywhere?

No. The calculator runs entirely in your browser. Nothing you enter is uploaded or stored on a server, and there is no registration or tracking in the tool.

Disclaimer

This calculator and article support preliminary engineering, screening, education and design. Equations follow ASME Section VIII Division 1 (2025 Edition) and the other codes named; material data and Table UCS-66 values in the tool are indicative and must be confirmed against ASME Section II Part D and the Code edition in your project specification. Results depend entirely on the inputs and stated assumptions. They do not replace a Code calculation package, vendor data, project specifications or review by a qualified engineer and acceptance by the Authorized Inspector. Always have pressure equipment designs reviewed by a competent engineer before fabrication or operation.

Aienginear Pressure Vessel Calculator (VesselCalc Pro Ultimate) · calculator v4.0.0 · article updated 27 October 2026 · standards status checked October 2026 · Published by Aienginear.com, Engineering Made Smarter. Found an error? Tell us.

Aienginear

Written by Muhammad Raza

Founder of Aienginear. Mechanical engineer (BSc, UET Lahore) and Head of Projects with 18+ years managing piping, mechanical installation, plant shutdowns and turnarounds in power, cement, fertilizer and oil & gas plants.

LinkedIn · YouTube · Report an error or ask a question

Leave a Comment