- Size rangeNPS 1/8 to 4 (DN 6 to 100). Class 6000 and 9000 SW stop at NPS 2.
- Class ≠ psiSW 3000/6000/9000 ↔ Sch 80 / 160 / XXS. Threaded 3000/6000 ↔ Sch 160 / XXS.
- 1.5 mm gapBack the pipe off the socket bottom before welding (B31.3-2024 Fig. 328.5.2-3).
- Fillet legCx ≥ the smaller of 1.09 × tn and the socket wall (B31.3-2024).
Coupling finder
Choose a size, end connection and class. The finder lists every governing dimension, the matching pipe schedule and the minimum socket-weld fillet size. You can copy the result into a datasheet or MTO.
Enable JavaScript to use the finder. All the data is also in the tables below.
What is a pipe coupling?
A pipe coupling is a short forged sleeve that joins pipe ends or provides a small-bore connection point. Couplings appear throughout process, power and utility piping. They are used to join lengths of small-bore pipe, add vents and drains, provide pressure and temperature instrument tappings, and attach chemical injection or sampling points to larger headers and vessels.
ASME B16.11 covers two coupling types:
- Full coupling. Sockets or internal threads at both ends join two pipes in line. A short web between the sockets (laying length E) stops the pipe from passing through.
- Half coupling. One socket or threaded end. The other end is a plain face that is welded onto a run pipe, header or vessel shell to create a branch, usually as a set-on or set-in fillet-welded connection.
Reducing couplings (different sizes at each end) are not tabulated in B16.11. They are supplied to the manufacturer’s standard, so always work from the certified drawing.
How to read the dimension letters
Many free online tables relabel the B16.11 dimensions, so the same letter can mean different things on different websites. This page keeps the letters used in ASME B16.11 itself, so a value can be checked straight against the standard or a manufacturer’s drawing.
| Letter | Meaning (ASME B16.11 convention) | Applies to |
|---|---|---|
| B (SW) | Socket bore diameter, given as maximum / minimum. It must clear the maximum pipe OD. | Socket-weld |
| C (SW) | Socket wall thickness, given as average / minimum. It is set to about 1.25 × the matching pipe wall. | Socket-weld |
| D (SW) | Bore (flow) diameter of the fitting, max / min. It is roughly the ID of the matching pipe schedule. | Socket-weld |
| J | Minimum socket depth, measured from the face to the socket bottom. | Socket-weld |
| E | Laying length of a full coupling, measured between the two socket bottoms. | SW full coupling |
| F | Half coupling length, measured from the socket bottom to the opposite (welding) end. | SW half coupling |
| W | End-to-end length of a threaded full coupling. | Threaded |
| B (THD) | Minimum length of full (perfect) internal thread. | Threaded |
| D (THD) | Minimum outside diameter of a threaded coupling, by class. | Threaded |
| L1, L2 | NPT hand-tight engagement and effective external thread length (ASME B1.20.1). | NPT threads |
Socket-weld coupling dimensions (ASME B16.11)
The pipe slides into a machined socket and is joined with an external fillet weld. Because the pipe sits inside the socket, it aligns itself easily and needs no bevelling. The trade-off is an internal crevice between the pipe end and the socket bottom.
Socket-weld coupling dimension table, NPS 1/8 to 4
| NPS | DN | Pipe OD | Socket bore B max / min | Bore D (max / min) | Socket wall C (avg / min) | Socket depth J min | Full cpl. E | Half cpl. F | Full cpl. overall ≥ E + 2J | ||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Cl. 3000 | Cl. 6000 | Cl. 9000 | Cl. 3000 | Cl. 6000 | Cl. 9000 | ||||||||
| 1/8 | 6 | 10.3 | 11.2 / 10.8 | 7.6 / 6.1 | 4.8 / 3.2 | — | 3.18 / 3.18 | 3.96 / 3.43 | — | 9.5 | 6.5 | 16.0 | 25.5 |
| 1/4 | 8 | 13.7 | 14.6 / 14.2 | 10.0 / 8.5 | 7.1 / 5.6 | — | 3.78 / 3.30 | 4.60 / 4.01 | — | 9.5 | 6.5 | 16.0 | 25.5 |
| 3/8 | 10 | 17.1 | 18.0 / 17.6 | 13.3 / 11.8 | 9.9 / 8.4 | — | 4.01 / 3.50 | 5.03 / 4.37 | — | 9.5 | 6.5 | 17.5 | 25.5 |
| 1/2 | 15 | 21.3 | 22.2 / 21.8 | 16.6 / 15.0 | 12.5 / 11.0 | 7.2 / 5.6 | 4.67 / 4.09 | 5.97 / 5.18 | 9.35 / 8.18 | 9.5 | 9.5 | 22.5 | 28.5 |
| 3/4 | 20 | 26.7 | 27.6 / 27.2 | 21.7 / 20.2 | 16.3 / 14.8 | 11.8 / 10.3 | 4.90 / 4.27 | 6.96 / 6.04 | 9.78 / 8.56 | 12.5 | 9.5 | 24.0 | 34.5 |
| 1 | 25 | 33.4 | 34.3 / 33.9 | 27.4 / 25.9 | 21.5 / 19.9 | 16.0 / 14.4 | 5.69 / 4.98 | 7.92 / 6.93 | 11.38 / 9.96 | 12.5 | 12.5 | 28.5 | 37.5 |
| 1 1/4 | 32 | 42.2 | 43.1 / 42.7 | 35.8 / 34.3 | 30.2 / 28.7 | 23.5 / 22.0 | 6.07 / 5.28 | 7.92 / 6.93 | 12.14 / 10.62 | 12.5 | 12.5 | 30.0 | 37.5 |
| 1 1/2 | 40 | 48.3 | 49.2 / 48.8 | 41.6 / 40.1 | 34.7 / 33.2 | 28.7 / 27.2 | 6.35 / 5.54 | 8.92 / 7.80 | 12.70 / 11.12 | 12.5 | 12.5 | 32.0 | 37.5 |
| 2 | 50 | 60.3 | 61.7 / 61.2 | 53.3 / 51.7 | 43.6 / 42.1 | 38.9 / 37.4 | 6.93 / 6.04 | 10.92 / 9.50 | 13.84 / 12.12 | 16.0 | 19.0 | 41.0 | 51.0 |
| 2 1/2 | 65 | 73.0 | 74.4 / 73.9 | 64.2 / 61.2 | — | — | 8.76 / 7.67 | — | — | 16.0 | 19.0 | 43.0 | 51.0 |
| 3 | 80 | 88.9 | 90.3 / 89.8 | 79.4 / 76.4 | — | — | 9.52 / 8.30 | — | — | 16.0 | 19.0 | 44.5 | 51.0 |
| 4 | 100 | 114.3 | 115.7 / 115.2 | 103.8 / 100.7 | — | — | 10.69 / 9.35 | — | — | 16.0 | 19.0 | 48.0 | 51.0 |
Dimensions per ASME B16.11-2021; pipe OD per ASME B36.10M. A dash (—) means B16.11 does not cover that size/class combination. Do not interpolate. The overall length (E + 2J) is an Aienginear-derived minimum; actual forgings may be longer, so check the manufacturer’s drawing for clearance-critical layouts. Inch values are converted from mm; for inch-based acceptance, use the standard’s own inch table, which may differ in the last digit.
Threaded coupling dimensions (ASME B16.11 / NPT)
A threaded coupling has tapered internal pipe threads, normally NPT to ASME B1.20.1. The joint seals by thread interference plus a compatible sealant. Threaded joints need no hot work at site, which suits low-hazard utility, air and instrument service. Many piping specifications restrict them in flammable, toxic, cyclic or high-vibration service.
Threaded (NPT) coupling dimension table, NPS 1/8 to 4
| NPS | DN | Pipe OD | Threads per inch | Full cpl. end-to-end W | Half cpl. ≈ W/2 | Min. full thread length B | NPT (ASME B1.20.1) | Coupling OD D (min) | ||
|---|---|---|---|---|---|---|---|---|---|---|
| L2 effective | L1 hand-tight | Cl. 3000 | Cl. 6000 | |||||||
| 1/8 | 6 | 10.3 | 27 | 32 | 16.0 | 6.4 | 6.70 | 4.10 | 16 | 22 |
| 1/4 | 8 | 13.7 | 18 | 35 | 17.5 | 8.1 | 10.21 | 5.79 | 19 | 25 |
| 3/8 | 10 | 17.1 | 18 | 38 | 19.0 | 9.1 | 10.36 | 6.10 | 22 | 32 |
| 1/2 | 15 | 21.3 | 14 | 48 | 24.0 | 10.9 | 13.56 | 8.13 | 28 | 38 |
| 3/4 | 20 | 26.7 | 14 | 51 | 25.5 | 12.7 | 13.86 | 8.61 | 35 | 44 |
| 1 | 25 | 33.4 | 11.5 | 60 | 30.0 | 14.7 | 17.34 | 10.16 | 44 | 57 |
| 1 1/4 | 32 | 42.2 | 11.5 | 67 | 33.5 | 17.0 | 17.95 | 10.67 | 57 | 64 |
| 1 1/2 | 40 | 48.3 | 11.5 | 79 | 39.5 | 17.8 | 18.38 | 10.67 | 64 | 76 |
| 2 | 50 | 60.3 | 11.5 | 86 | 43.0 | 19.0 | 19.22 | 11.07 | 76 | 92 |
| 2 1/2 | 65 | 73.0 | 8 | 92 | 46.0 | 23.6 | 28.89 | 17.32 | 92 | 108 |
| 3 | 80 | 88.9 | 8 | 108 | 54.0 | 25.9 | 30.48 | 19.46 | 108 | 127 |
| 4 | 100 | 114.3 | 8 | 121 | 60.5 | 27.7 | 33.02 | 21.44 | 140 | 159 |
W, B and D per ASME B16.11-2021; thread data per ASME B1.20.1-2013 (R2018). The half-coupling length shown as W/2 is a nominal reference. Confirm the length with the supplier. Threaded couplings and half couplings are made only in Class 3000 and 6000.
Classes, pressure rating and pipe schedules
ASME B16.11 does not publish a pressure value for each class. Instead, a fitting is rated equal to straight seamless pipe of the matching schedule, in an equivalent material, at the same temperature. You calculate the coupling’s allowable pressure the same way you would for that pipe, using your piping code. Threaded fittings pair with a heavier schedule than socket-weld fittings of the same class because cutting the thread removes wall material.
| End type | Class 2000 | Class 3000 | Class 6000 | Class 9000 |
|---|---|---|---|---|
| Socket-weld | — | Sch 80 / XS (NPS 1/8–4) | Sch 160 (NPS 1/8–2) | XXS (NPS 1/2–2) |
| Threaded | Sch 80 / XS (elbows, tees, crosses only, not couplings) | Sch 160 | XXS | — |
Matching pipe wall thickness by schedule
| NPS | DN | Pipe OD | Sch 80 / XS wall | Sch 160 wall | XXS wall |
|---|---|---|---|---|---|
| 1/8 | 6 | 10.3 | 2.41 | — | — |
| 1/4 | 8 | 13.7 | 3.02 | — | — |
| 3/8 | 10 | 17.1 | 3.20 | — | — |
| 1/2 | 15 | 21.3 | 3.73 | 4.78 | 7.47 |
| 3/4 | 20 | 26.7 | 3.91 | 5.56 | 7.82 |
| 1 | 25 | 33.4 | 4.55 | 6.35 | 9.09 |
| 1 1/4 | 32 | 42.2 | 4.85 | 6.35 | 9.70 |
| 1 1/2 | 40 | 48.3 | 5.08 | 7.14 | 10.15 |
| 2 | 50 | 60.3 | 5.54 | 8.74 | 11.07 |
| 2 1/2 | 65 | 73.0 | 7.01 | 9.53 | 14.02 |
| 3 | 80 | 88.9 | 7.62 | 11.13 | 15.24 |
| 4 | 100 | 114.3 | 8.56 | 13.49 | 17.12 |
A dash means that schedule is not listed in ASME B36.10M for the size. In those cases, take the pipe wall from your project’s piping class.
Socket-weld vs threaded couplings
| Criterion | Socket-weld coupling | Threaded (NPT) coupling |
|---|---|---|
| Leak tightness | Very good. The fillet weld forms a permanent seal. | Depends on thread quality and sealant. It is a possible leak path in vibration or thermal cycling. |
| Site work | Needs qualified welders, a WPS and hot-work permits. | No hot work. Fast to install and dismantle. |
| Classes | 3000 / 6000 / 9000 | 3000 / 6000 |
| Internal crevice | Yes, at the socket bottom gap. Avoid it in crevice-corrosion or erosive service. | Thread roots act as notches and crevices. |
| Fatigue | Fair. B31.3-2024 para. 311.2.2 bars socket welds above NPS 2 in severe cyclic service. | Poor. Seal welding or a change of joint type is common in cyclic service. |
| Typical use | Hydrocarbon, steam, high-pressure small bore, instrument roots | Utility air, water, lube oil, instrument connections where the spec allows |
How to select the right coupling
- Start from the piping class. Your project’s piping material specification names the coupling type, class, material and end connection for each service and size range. Work from that rather than the catalogue.
- Fix the size. NPS is a name, not a measurement. NPS 1 pipe is 33.4 mm OD. Use DN only where the spec does.
- Choose the end type. Socket-weld is the usual choice for hydrocarbon, steam and high-pressure small bore. Threaded is used where the spec allows and dismantling or no hot work matters.
- Match the class to the pipe schedule. Use Table 4 above (see also pipe sizes and schedules). Check that the size/class combination exists. For example, Class 9000 SW is not made in NPS 3.
- Confirm the material. Specify the forging grade to suit the pipe and design temperature, for example ASTM A105, A350 LF2 (low temperature), A182 F316L or F11. Add impact testing, NACE MR0175 / ISO 15156 or PMI where the service requires them.
- Check branch reinforcement for half couplings welded to headers or vessels. If the half coupling cannot meet the code, switch to an MSS SP-97-2025 integrally reinforced outlet.
- Write a complete purchase description. Example: “Half coupling, NPS 1, Class 3000, SW, ASTM A105N, ASME B16.11-2021, EN 10204 3.1 certificate.”
Installation and inspection
Socket-weld joints
- Cut the pipe square and deburr it. Insert it until it bottoms out, mark it, then withdraw it about 1.5 mm (1/16 in) before tacking. ASME B31.3-2024 (Fig. 328.5.2-3) and B31.1 show this gap before welding. Gap gauges or rings make it repeatable.
- Minimum fillet leg Cx is the smaller of 1.09 × tn (tn = nominal pipe wall) and the socket wall thickness. The weld must not undercut the socket wall.
- Weld to a qualified WPS with qualified welders. Carry out VT plus MT or PT as required by the code and the fluid category. Socket welds cannot be radiographed effectively, so surface examination is the norm.
- Pipe: NPS 1 Sch 80, OD 33.4 mm, nominal wall tn = 4.55 mm (Table 5).
- Coupling: socket bore B 34.3 / 33.9 mm clears the pipe; socket depth J ≥ 12.5 mm; laying length E = 12.5 mm (Table 2).
- Fit-up: with a 1.5 mm gap at each socket bottom, the two pipe ends sit about E + 2 × 1.5 = 15.5 mm apart, and each pipe engages at least 12.5 − 1.5 = 11.0 mm of socket.
- Fillet weld: 1.09 × 4.55 = 4.96 mm, which is less than the 5.69 mm average socket wall, so the minimum leg Cx ≈ 5.0 mm.
- Spool cutting: deduct about 15.5 mm from the face-to-face run for each in-line full coupling when you cut the pipe.
Threaded joints
- Gauge the threads (L1 ring and plug gauges). Reject torn, galled or contaminated threads.
- Use only the sealant or PTFE tape your service specification allows. Keep it off the first thread so it does not enter the line.
- Make up the joint hand-tight, then about three turns with a wrench. Do not back off a joint to align it. Turn it forward or remake it.
- If the specification calls for seal welding, do it without thread compound and cover all exposed threads.
Receiving inspection
- Check the marking: manufacturer, material grade, class, size and B16.11. Then check the mill certificate for heat-number traceability.
- Spot-check socket bore B, socket depth J and bore D with calipers or a depth gauge against Table 2. For threaded fittings, check gauge stand-off.
Common mistakes to avoid
- Reading “Class 3000” as 3000 psi. The rating depends on the matching pipe schedule, the material and the temperature.
- Ordering Class 6000 or 9000 socket-weld fittings above NPS 2, or threaded couplings in Class 9000. Neither is standard.
- Bottoming the pipe in the socket with no expansion gap. This leads to cracked fillet welds.
- Applying ASME B16.9 butt-weld fitting tolerances to forged B16.11 couplings. They are different products with different tolerance tables.
- Assuming every threaded coupling is NPT. BSPT (ISO 7-1) and NPTF exist and do not seal against NPT.
- Welding a half coupling onto a header without a reinforcement check.
- Taking dimensions from an unverified online table. See the next section.
Errors corrected from commonly published tables
Before we published these tables, we checked every value against ASME B16.11-2021, B1.20.1 and B36.10M. Several coupling tables that circulate online contain the following errors, which we have corrected:
- NPS 4 socket bore. Some tables give 103.8 / 100.7 mm, which is actually the NPS 4 Class 3000 bore, and is smaller than the 114.3 mm pipe it must accept. The correct socket bore is 115.7 / 115.2 mm.
- Swapped letters. Socket wall and bore are often labelled “D” and “C”, the reverse of B16.11. Socket depth and laying length are often renamed “L1” and “L2”. We use the standard’s letters (C, D, J, E, F).
- Thread columns. The longer “thread length” column in many tables is actually L2, the effective pipe thread length from B1.20.1, not a coupling dimension. Both now appear with clear labels.
- “OD = B + D”. This expression has no meaning in B16.11 and has been removed. Socket-weld coupling OD follows from the socket bore plus twice the socket wall.
- B16.9 tolerance tables. Butt-welding fitting tolerances are sometimes appended to coupling pages. They do not apply to forged socket-weld or threaded couplings.
Pipe coupling dimensions quiz
Ten questions on ASME B16.11 couplings, drawn from the tables and checks above. Pick an answer to see whether it is right and why. Your score appears at the end.
Quiz answers follow ASME B16.11-2021, ASME B1.20.1, ASME B36.10M and ASME B31.3-2024 as summarised on this page. For procurement and acceptance, use the licensed standard and your project piping specification.
Frequently asked questions
Which standard covers socket-weld and threaded pipe coupling dimensions?
ASME B16.11 (current edition 2021) covers the dimensions, tolerances, pressure ratings, marking and material requirements of forged socket-welding and threaded couplings and half couplings from NPS 1/8 to NPS 4. NPT thread form and gauging come from ASME B1.20.1.
What is the difference between a full coupling and a half coupling?
A full coupling has a connection at both ends and joins two pipes in line. A half coupling has a single socket or threaded end; its other end is welded onto a pipe, vessel or header to create a small branch, vent, drain or instrument tapping.
What pressure classes are available for pipe couplings?
Socket-weld couplings are made in Class 3000, 6000 and 9000. Threaded couplings and half couplings are made in Class 3000 and 6000 only; Class 2000 in ASME B16.11 applies to threaded elbows, tees and crosses, not couplings. Class 6000 and 9000 socket-weld couplings stop at NPS 2.
Is Class 3000 the pressure rating in psi?
No. The class is a designation, not a pressure. ASME B16.11 rates a fitting at the same pressure-temperature rating as seamless pipe of the matching schedule and material. For example, a Class 3000 socket-weld coupling is matched to Schedule 80 pipe.
What pipe schedule matches each coupling class?
For socket-weld fittings: Class 3000 matches Schedule 80/XS, Class 6000 matches Schedule 160 and Class 9000 matches XXS. For threaded fittings: Class 3000 matches Schedule 160 and Class 6000 matches XXS, because the threads remove wall material.
What gap is required at the bottom of a socket-weld coupling?
ASME B31.3-2024 (Fig. 328.5.2-3) and B31.1 call for the pipe to be withdrawn about 1.5 mm (1/16 in) from the bottom of the socket before welding. The gap lets the weld contract without cracking the fillet weld.
How large should the fillet weld be on a socket-weld coupling?
Under ASME B31.3-2024, the minimum fillet weld leg Cx is the smaller of 1.09 times the pipe's nominal wall thickness and the socket wall thickness. Use the coupling finder on this page to get the value for your size and class.
Can these dimensions be used for purchasing?
Use them for design and preliminary checks only. Before you buy or fabricate, confirm the final dimensions against the licensed ASME B16.11 standard, the manufacturer's certified drawing and your project piping specification.
Standards and references
- ASME B16.11-2021, Forged Fittings, Socket-Welding and Threaded (current edition). asme.org
- ASME B1.20.1-2013 (R2018), Pipe Threads, General Purpose (Inch). asme.org
- ASME B36.10M-2022, Welded and Seamless Wrought Steel Pipe (pipe OD and wall thickness).
- ASME B31.3-2024, Process Piping: socket weld limits (para. 311.2.2), gap and fillet size (Figs. 328.5.2-2 and 328.5.2-3), branch reinforcement (para. 304.3).
- ASME B31.1, Power Piping: socket weld fit-up for steam and boiler external piping.
- MSS SP-97-2025, Integrally Reinforced Forged Branch Outlet Fittings.
- ASME B16.9-2024, Factory-Made Wrought Buttwelding Fittings (shown only to explain why its tolerances do not apply here).
Test yourself: take the Pipe Coupling Dimensions Quiz on this page: 10 ASME B16.11 questions with explained answers.
Related Aienginear guides and tools: What is an industrial pipe? · Pipe sizes & schedules · Types of pipe fittings · Pipe elbow dimensions · Pipe tee dimensions · Pipe reducer dimensions · ASTM A105 forgings · Pipe fittings inspection · Pipe Support Spacing Calculator · Hydrotest Calculator
Aienginear — AI-driven process & industrial engineering
This page is for engineering education, design and preliminary selection. ASME standards are copyrighted. This article summarises their dimensional data for reference and does not replace the licensed standard. Before you procure, fabricate or accept fittings, confirm every critical dimension against the current licensed ASME B16.11, the manufacturer's certified drawing and your project piping specification.